Home › Garage door opener not working? A troubleshooting checklist
Garage door opener not working? A troubleshooting checklist
Many "broken opener" calls turn out to be a dead battery, a tripped breaker or a bumped sensor. Work through these checks first. If none of them fixes it, you'll at least be able to tell the contractor exactly what happens.
1. Nothing happens at all
- Is the opener plugged in? Does the light on the motor unit come on?
- Check the breaker panel and any GFCI outlet in the garage (press reset).
- If the wall button works but the remote doesn't, replace the remote battery.
- Look for a lock or vacation button on the wall control. When it's on, remotes are ignored.
2. The door starts to close, then goes back up
This is usually the safety sensors (the two small boxes near the floor on each side of the door).
- Remove anything in the way: a bin, a bike, leaves, snow.
- Wipe both lenses with a soft cloth.
- Check the little lights. On most brands a steady light means aligned, and a blinking or off light means they can't see each other. Gently line them up and tighten the bracket.
- Check that the thin wires to the sensors aren't cut or pulled loose.
These sensors and the auto-reverse are required by federal safety rules for openers made since 1993 (16 CFR Part 1211). Never tape over, bypass or disconnect them.
3. The motor hums but the door doesn't move
- The emergency release (red cord) may have been pulled. The opener runs but isn't connected to the door. Your manual shows how to reconnect it.
- A stripped drive gear or broken chain/belt can cause this too. That's a repair job.
- A broken spring can also make the opener too weak to lift the door.
4. The door stops short, or reverses as soon as it touches the floor
The open/close travel limits or the force setting may need adjusting. Many openers have limit buttons or screws; the steps differ by brand, so follow your opener's manual. After any change, test the auto-reverse the way the manual describes.
5. Loud grinding, or the door jerks
Could be worn rollers, a dry track, a loose chain or a worn gear. Leave adjustments of the tracks, cables and springs to a pro.
Repair or replace the opener?
| Repair usually makes sense when… | Replacing may make sense when… |
|---|---|
| The opener is fairly new, and it's one part (sensor, gear, remote, board) | The opener is old, the repair is a big share of a new unit's price, or parts aren't available |
| It's a setting or alignment problem | You want features it lacks: quieter belt drive, battery backup, phone control |
What does opener repair cost?
| Source (viewed Nov 2026) | Typical price |
|---|---|
| HomeAdvisor | Average about $234; most pay $124–$368 |
| Angi (2025 data) | $100–$500 for opener repair |
| Inch Calculator (2026) | About $180–$360 |
National estimates, not Naperville quotes and not our prices. See the full repair cost guide.
Sources
- 16 CFR Part 1211, Safety Standard for Automatic Residential Garage Door Operators, ecfr.gov.
- HomeAdvisor, "How Much Does Garage Door Opener Repair Cost?", homeadvisor.com — viewed Nov 2026.
- Angi, "How Much Do Garage Door Repairs Cost?" (2025 data), angi.com — viewed Nov 2026.
- Inch Calculator, "Cost to Repair a Garage Door – 2026 Price Guide", inchcalculator.com — viewed Nov 2026.
Tell us what's wrong. We pass your request to one independent local contractor. Free, no obligation. We are a referral service, not a contractor.
Request help — takes 1 minuteMore guides
- Garage door spring replacement in Naperville
- Garage door repair cost in Naperville
- Winter garage door problems (and how to prevent them)
- Questions to ask a garage door company before you hire
Last updated November 2026. Written by Sunny Patel, who runs this referral service. We are not garage door technicians; this is general information gathered from the sources named on this page, not professional advice.